Floor diffusers

layer

The AFG Type floor grille is developed to be mounted on raised floor systems to match typical 600mm by 600mm floor tiles, to supply cooling to computer rooms or data centers where cooling load is high. Two different types of sub-frame are available to suit different raised floor systems typically available in the market.

This is heavy duty floor grille capable of taking high static load and is robust in construction.

The floor grille was tested independently for:
A. Uniform distributed load test at 12kN/m³
B. Static load (Concentrated Load): Tested at 4.5 kN over an area of 25 mm x 25 mm.
C. Safety load: The sample was successfully tested at 13.5 kN at the centre of the grille over an area of 25 mm x 25.
D. Soft Body Impact Test: The grille did not collapse

The above tests were conducted in accordance with UK´s standard MOB PF2 PS/SPU: 1992. The core of the floor grille is in mill finish. the grille can be supplied with either 0° or 15° deflection blade profile. The steel sub-frame below the grille core is painted matt black in RAL 9005 as standard supply

read more

layer

Type SDRF

  • With the TROX staircase swirl diffuser type SDRF low air volumes are discharged into the room and the velocity is quickly reduced, so that, for instance in theatres, every single seat is draughtfree and silently supplied with fresh air.

read more

layer

Type FBA · FBK

  • These floor diffusers have been designed to withstand very heavy usage.
  • Can be used with and without a border unit.
  • Control of discharge characteristics and unit flow rate are available as accessories which fit into the dirt trap.

read more

layer

  • TROX 3-speed fan terminal units with TROX “FBA/250” Type circular floor diffuser in die cast aluminium complete with wall mounted temperature sensor to each unit.
  • The wall sensor allows the building occupants to adjust the room set point temperature, and the fan speed manually or automatically.

read more

layer

ARR

Roll down grilles with rounded blade edges, for covering floor voids such as trenches for heating, underfloor induction units, decentralised ventilation units, light wells and similar

  • Nominal width: 150, 200, 250, 300, 350, 400, 450 mm
  • Grille height 15 or 20 mm
  • Fixed transverse blades made of aluminium
  • Cut sections and rolls to be cut to length
  • Good impact sound insulation, quiet to walk on and non slip due to rubber underside
  • Cut edges of blades are covered

read more

layer

The TROX CFG floor grille is the similar like AFG where it has been specifically developed for mounting in Raised Access Floors in such areas as Computer Rooms, where load and damage resistance are of the utmost importance.
Having a rating of extra heavy duty to the latest specifications, the CFG can replace 600mm square floor tiles to handle supply air. Grille border can be specified to suit the type of floor system used. A range of surface finishes is available.
Unlike AFG, CFG is having two options of fan to greatly assist supply air to room. CFG-AC is giving a constant airflow while CFG-EC airflow is proportional by 0-10Vdc signal.

read more

layer

Type SD

  • TROX staircase swirl diffusers type SD can be used for horizontal or angled air flow depending on the requirements of the location.
  • Depending on the architectural requirements, the staircase swirl diffuser can be made circular or square.

read more

VISUALISATION OF AIR FLOW - FLOOR DIFFUSERS DIFFUSER

In the TROX Air flow studio, the flow behavior of the air with various air distribution system is made impressively visible. The introduction of smoke in an authentic situation with space heat load simulators shows real flow patterns.

Share page

Recommend this page

Recommend this page by sending a link by mail.

Fields marked with an (*) are required fields.

Share page

Thank you for your recommendation!

Your recommendation has been sent and should arrive shortly.


Contact

We are here for you

Visual contact Visual contact

Please specify your message and type of request.
Tel.: +61 (02) 8923 2551

Fields marked with an (*) are required fields.

Contact

Thank you for your message!

Visual contact Visual contact

Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +61 (02) 8923 2551

Contact

We are here for you

Visual contact Visual contact

Please specify your message and type of request.
Tel.: +61 (02) 8923 2551

Attachment (max. 10MB)

Fields marked with an (*) are required fields.

Contact

Thank you for your message!

Visual contact Visual contact

Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +61 (02) 8923 2551